User Tag List

Thanks Thanks:  0
Likes Likes:  0
Page 1 of 2 12 LastLast
Results 1 to 10 of 12

Thread: now you see them zorsts part 2

  1. #1
    Regular Member
    Join Date
    Oct 2005
    Location
    south yorkshire
    Post Thanks / Like
    Mentioned
    0 Post(s)
    Tagged
    0 Thread(s)
    StatsVehicle Info
    Post Thanks / Like
    Mentioned
    0 Post(s)
    Tagged
    0 Thread(s)

    Default now you see them zorsts part 2

    fitted these today,bit of a pain but well worth it i think.following cb500t's idea i decided to fit the new valence and have also fitted two jetex stainless exhaust trims.the original exhaust just required the bends cutting off,and then the new ends just slipped on and are held in place by clamps.top job or what!

  2. #2
    Regular Member Jamie's Avatar
    Join Date
    Jun 2005
    Location
    Worcestershire
    Post Thanks / Like
    Mentioned
    0 Post(s)
    Tagged
    0 Thread(s)
    StatsVehicle Info
    Post Thanks / Like
    Mentioned
    0 Post(s)
    Tagged
    0 Thread(s)

    Default

    Looks good mate... very effective indeed!

  3. #3
    Regular Member
    Join Date
    Oct 2005
    Location
    The Blackburn End
    Post Thanks / Like
    Mentioned
    0 Post(s)
    Tagged
    0 Thread(s)
    StatsVehicle Info
    Post Thanks / Like
    Mentioned
    0 Post(s)
    Tagged
    0 Thread(s)

    Default

    Was your original exhaust a drop down sort ?

  4. #4
    Regular Member
    Join Date
    Oct 2005
    Location
    south yorkshire
    Post Thanks / Like
    Mentioned
    0 Post(s)
    Tagged
    0 Thread(s)
    StatsVehicle Info
    Post Thanks / Like
    Mentioned
    0 Post(s)
    Tagged
    0 Thread(s)

    Default

    yes mate they were the hidden type.looks the part now though.

  5. #5
    [Ex]Admin Duncan's Avatar
    Join Date
    Jun 2005
    Location
    East Sussex
    Post Thanks / Like
    Mentioned
    0 Post(s)
    Tagged
    0 Thread(s)
    StatsVehicle Info
    Post Thanks / Like
    Mentioned
    0 Post(s)
    Tagged
    0 Thread(s)

    Default

    Deffo good idea getting the cutout valence. Looking good Gary!

    D

  6. #6
    Regular Member
    Join Date
    Oct 2005
    Location
    south yorkshire
    Post Thanks / Like
    Mentioned
    0 Post(s)
    Tagged
    0 Thread(s)
    StatsVehicle Info
    Post Thanks / Like
    Mentioned
    0 Post(s)
    Tagged
    0 Thread(s)

    Default

    cheers matey,will post some better pictures once its had a good polish and in better light conditions ie daylight.

  7. #7
    Regular Member
    Join Date
    Jul 2005
    Location
    Newcastle upon Tyne
    Post Thanks / Like
    Mentioned
    0 Post(s)
    Tagged
    0 Thread(s)
    StatsVehicle Info
    Post Thanks / Like
    Mentioned
    0 Post(s)
    Tagged
    0 Thread(s)

    Default

    Looks good........

  8. #8
    Regular Member
    Join Date
    Jul 2005
    Location
    Newcastle upon Tyne
    Post Thanks / Like
    Mentioned
    0 Post(s)
    Tagged
    0 Thread(s)
    StatsVehicle Info
    Post Thanks / Like
    Mentioned
    0 Post(s)
    Tagged
    0 Thread(s)

    Default

    Which Jetex tails did you use,as their are a few to choose.....

  9. #9
    Regular Member
    Join Date
    Oct 2005
    Location
    south yorkshire
    Post Thanks / Like
    Mentioned
    0 Post(s)
    Tagged
    0 Thread(s)
    StatsVehicle Info
    Post Thanks / Like
    Mentioned
    0 Post(s)
    Tagged
    0 Thread(s)

    Default

    hi mate, i used the following u236310 ellips xl 63.they are 2.5 inch diamiter.you will need a reducing sleave for one side as you will find its 2.0 inches.the above is stainless steel.hope this helps.fits just nice in the cutouts without touching any plastic.

  10. #10
    Regular Member
    Join Date
    Jul 2005
    Location
    Newcastle upon Tyne
    Post Thanks / Like
    Mentioned
    0 Post(s)
    Tagged
    0 Thread(s)
    StatsVehicle Info
    Post Thanks / Like
    Mentioned
    0 Post(s)
    Tagged
    0 Thread(s)

    Default

    So thats 2no u236310's and what else?,is the reducer a Jetex part?

Page 1 of 2 12 LastLast

Thread Information

Users Browsing this Thread

There are currently 1 users browsing this thread. (0 members and 1 guests)

Similar Threads

  1. New Zorsts!
    By parapaul in forum Diesel Engine related
    Replies: 23
    Last Post: 24th October 2007, 18:16
  2. Zorsts On!!
    By payney in forum Quick Photo Album
    Replies: 45
    Last Post: 19th August 2007, 20:42
  3. Zorsts on
    By Spikey© in forum Quick Photo Album
    Replies: 5
    Last Post: 28th April 2006, 22:03
  4. de-cat zorsts!!!
    By markspark in forum Petrol Engine related
    Replies: 0
    Last Post: 20th March 2006, 20:44
  5. 1.8 Vs 2.2 zorsts
    By Spikey© in forum Vectra C / Signum Car Chat
    Replies: 12
    Last Post: 20th February 2006, 17:06

Visitors found this page by searching for:

Nobody landed on this page from a search engine, yet!

Bookmarks

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •