-
5th December 2016, 11:22
#1
Regular Member
Help needed with electrics please
Hi I have just bought a car from a well know guy on here @Slammedorion and it is perfect.. I am needing a little help to wire in the heated front seats and also the rear windows , I know the bulk of the work is done and i just need to fit the body loom.. I have all the wiring needed but electrics is something I don't understand haha , if any one could help I would be more than grateful.. Will to travel also PLEASE
-
6th December 2016, 01:36
#2
-
6th December 2016, 02:50
#3
Happy to do it for u mate just need to figure out when i am closer up north.
all the help you after can be found here.
Vectra SRi estate 165/230 CDTI 2006 XP
Stret & Teapot tuned, fully blanked and deleted EGR, Precat & DPF deleted, FMIC, Silicone & alloy boost pipes, 4 bar TMAP Sebastian 56 small 7 blade turbo & 2.0 Injectors
-
Post Thanks / Like - 0 Thanks, 2 Likes
-
6th December 2016, 09:01
#4
Regular Member
Originally Posted by
jaguser
Happy to do it for u mate just need to figure out when i am closer up north.
That would be great thanks , I thought there might be a few more people up this way that is good with electrics but looks like that not the case
-
6th December 2016, 21:33
#5
i am actually not good with electric but it is basically lego. position - pin - in - click -next
all the help you after can be found here.
Vectra SRi estate 165/230 CDTI 2006 XP
Stret & Teapot tuned, fully blanked and deleted EGR, Precat & DPF deleted, FMIC, Silicone & alloy boost pipes, 4 bar TMAP Sebastian 56 small 7 blade turbo & 2.0 Injectors
-
7th December 2016, 00:48
#6
Regular Member
Originally Posted by
jaguser
i am actually not good with electric but it is basically lego. position - pin - in - click -next
Well I can deffo say you will be better than me,,, all the work is done in the doors and switches for the heated seats , just got to fit the body looms, cut existing wires in the car and solder the ones from the looms plus fit the extra cables needed it's all here nod has all been activated too
-
7th December 2016, 07:03
#7
I can do it only if u have loom with pins mate.if there is cutting loom needed u cant solder it in the plugs. Not sure if i understand what u mean.the loom should have pins on wires.there shouldn't be any cutting involved in your car.if u dont have such a loom i suggest to contact @ppasma and buy from him ready tonfit loom.its not expensive
all the help you after can be found here.
Vectra SRi estate 165/230 CDTI 2006 XP
Stret & Teapot tuned, fully blanked and deleted EGR, Precat & DPF deleted, FMIC, Silicone & alloy boost pipes, 4 bar TMAP Sebastian 56 small 7 blade turbo & 2.0 Injectors
-
7th December 2016, 09:48
#8
Regular Member
Originally Posted by
jaguser
I can do it only if u have loom with pins mate.if there is cutting loom needed u cant solder it in the plugs. Not sure if i understand what u mean.the loom should have pins on wires.there shouldn't be any cutting involved in your car.if u dont have such a loom i suggest to contact @ppasma and buy from him ready tonfit loom.its not expensive
Hi when SLAMMEDORION had the car he bought a donor car and removed all the bits that he needed... He removed the body looms from that car to, the wires that are not in my car are in these looms with the pins still intact to make the windows and seats work. But he cut the rest of the wires , these are the wires that is the same as in my car so these wires are the ones that require soldering... Hope this makes sense haha
-
7th December 2016, 09:51
#9
So if i understand front that removed loom theneeded wires can be separated and no need cutting or soldering as this should be very easy.
On the other side u would need an expert in soldering to solder all the wires and hope for no cold joint.
Can u post some pic of the removel loom?
all the help you after can be found here.
Vectra SRi estate 165/230 CDTI 2006 XP
Stret & Teapot tuned, fully blanked and deleted EGR, Precat & DPF deleted, FMIC, Silicone & alloy boost pipes, 4 bar TMAP Sebastian 56 small 7 blade turbo & 2.0 Injectors
-
7th December 2016, 10:01
#10
Regular Member
Yes that is correct the loom s I have have the correct plugs ant the wires that are needed still have the contacts on , so yes these wires can be removed and then added to the existing looms. But I do not know how to de pin them haha
Bookmarks