factory park pilot

[squirrell25]

IMG_0016.jpgright i have got the inside of my signum in bits at the moment to fit the park pilot module i have found the white plug behind the fuse box but can't find the second plug for it

i have found 2 other plugs both black running along with the loom that come out behind the cover for the rear lights
is one of the 2 black plugs i found the other one i need

do i need to use both sockets on the module?

i am installing front and rear systems

[kenp]

Its at White and a Black plug thats neede to fic factory parkpilot. The second Black plug Might be for TPMS (not sure)

[BigWilko]

Right, you're about to have a massive sad face! The one that's NOT wrapped up in foam is the connector for the rear sensors. The one you have missing is the one for the front sensors & canbus control. It should run down the passenger side conduit and come out near the module. If it's not there you'll need to get someone to make it up for you or go to a scrappers, find a car with factory pp and strip it out. IT'S A SWINE! It runs down the rear wheel arch, throuh both conduits under the passenger doors, up behind the glove box, throught the bulkhead gromit and into the connector block just under the scuttle tray!

[squirrell25]

hi the two plugs in the pic were wrapped up in foam which came out by the rear light cluster cover the white plug which I haven't pictured was behind the fuse box my signum as got the wires going to the plug for the front bumper loom and the switch in the dash which lights up when the lights are turned on does this still mean I will have to have the other loom made upIMG_0016.jpg

[kenp]

Take a picture of the white plug.. as one is 12 pin and one is 18 pin if i remember..

[andy.l]

the factory fit pp plugs are bith black which 1 is a 18 pin and tge other
is a 12 pin.

the aftermarket wiring harness that you fit for rear pp
is 18 pin black plug and a 12 pin grey plug

the tpms black plug is also a 12 pin so if you have a look
at the 12 pin black plug and see if its got a black,green,brown,
green/yellow,brown/white,brown/red and black/white then
thats for tpms

[squirrell25]

the factory fit pp plugs are bith black which 1 is a 18 pin and tge other
is a 12 pin.

the aftermarket wiring harness that you fit for rear pp
is 18 pin black plug and a 12 pin grey plug

the tpms black plug is also a 12 pin so if you have a look
at the 12 pin black plug and see if its got a black,green,brown,
green/yellow,brown/white,brown/red and black/white then
thats for tpms

ok here go's

the black 12 way as got to be the tpms plug as the colours match up the the above qoute
the black 18 way plug as only got 5 wires going to it they as follows

pins 1-9 empty
pin 10 = brown
pin 11 = empty
pin 12 = red
pin 13 = empty
pin 14 = empty
pin 15 = brown/white stipe
pin 16 = empty
pin 17 = green
pin 18 = white


the white plug i found behind the fuse box is actuly grey
it a 12 way wires as follows
pin1 = black/white stripe
pin2 = brown/white stripe
pin3 = yellow/purple stripe
pin4 = yellow/white stripe
pin5 = yellow/red stipe
pin6 = yellow
pin7 = black
pin8 = brown
pin9 = empty
pin10 = empty
pin11 = empty
pin 12 = empty

IMG_0023.jpg

[andy.l]

yes that grey plug is for the rear park pilot that runs
to the inner back panel plug then the pp
bumper harness plugs into it.

you now only need the wiring harness to add to the
car from the rec with an 18 pin plug on to the front
under bonnet x26 multiplug were it connects to the front
harness thatvruns to the front bumper.

have you checked to see if you have this front
part of the harness from multiplug to front bumper

have you also got the plug behind the blank in were
the pp switch goes.

[squirrell25]

yes that grey plug is for the rear park pilot that runs
to the inner back panel plug then the pp
bumper harness plugs into it.

you now only need the wiring harness to add to the
car from the rec with an 18 pin plug on to the front
under bonnet x26 multiplug were it connects to the front
harness thatvruns to the front bumper.

have you checked to see if you have this front
part of the harness from multiplug to front bumper

have you also got the plug behind the blank in were
the pp switch goes.

hi i have got the plug behind the blank for p/p switch (i have already put the swicth in which lights up when th lights are on)
i have the harrnes to the front bumper with all pins wired (see pic)

IMG_0025.jpg

[andy.l]

hi i have got the plug behind the blank for p/p switch (i have already put the swicth in which lights up when th lights are on)
i have the harrnes to the front bumper with all pins wired (see pic)

IMG_0025.jpg

excellent so all you need now is the add on harness
from pp module to the front multiplug.