CDTI only Which Eibach spring kit did you fit

[Thunder]

Hi all well after my third VX Spring break i need some help

CDTI only Which Eibach spring kit did you fit

And what are your thoughts on them
the roads around me are full of pot holes so i don't want to go too low

I Know after reading on here that some think the Eibach kit
Part Number:10-65-007-02-22 sits too high at the front

My Axle Weight is
1065 front
985 rear
2006 Vectra Elite 1.9 CDTI
manual gearbox
fitted with 18" wheels & sports suspension from the factory

Cheers for helping me pick a set

i did email Eibach
but it just got me more confused
Eibach reply below

Thank you for your email regarding springs for your Vectra C

The difference is that there is a difference in front axle load. The E10-65-007-01-22 is for 1068kg front axle load and the E10-65-007-02-22 is for 1135kg front axle load

You should be able to find the axle weight of your car on the vin plate

I've looked all over the web & the kit E10-65-007-01-22 usually shows up as upto 1060kg

[Ian S100]

CDTi 150 BSRi: I've not actually fitted them yet but I have a full set of Bilstein B6's & the 'E10-65-007-02-22' all boxed up & waiting to be fitted.

I also emailed Eibach prior to purchase & got the twin of your email in reply

[aerodynamic18]

tbh i rang lmf and told them the weights and they sent me a set and tbh im happy not to high and feels really good now. looking forward to the car settling befroe i know the highs

[Thunder]

lol I'm now also after the spring mod plastic cover (part number 13178463)

i found both springs sets for £154 on line with free delivery

just don't know which set to get

Cheers for the reply

[happypostie]

i voted for the second set as ive a elite and this is what lmf said i needed,the front does sit a little high but was told it is the way the front arch shaped ,im happy with this setup . khalid

[Ian S100]

lol I'm now also after the spring mod plastic cover (part number 13178463)

i found both springs sets for £154 on line with free delivery

just don't know which set to get

Cheers for the reply

You have the Vectra Elite 1.9 CDTi so need the same part number as above - go on LMF website select spring, car then axle weight as on the plate by the drivers door

[Thunder]

Cheers Ian
E10-65-007-02-22 This was the kit i was going to get but then i read on here it sits high,
And then i emailed Eibach & it came back as i needed E10-65-007-01-22
i'll have to phone them tomorrow & see with they recommend for my front axle load which is 1065kg

Thank for the replys

[Ian S100]

lol I'm now also after the spring mod plastic cover (part number 13178463)

i found both springs sets for £154 on line with free delivery

just don't know which set to get

Cheers for the reply

With sport spings you need the 13178464 sleeves, they're slightly bigger diameter & green

[Ian S100]

Cheers Ian
E10-65-007-02-22 This was the kit i was going to get but then i read on here it sits high,
And then i emailed Eibach & it came back as i needed E10-65-007-01-22
i'll have to phone them tomorrow & see with they recommend for my front axle load which is 1065kg

Thank for the replys

I'll stick to slightly high, I give the drive a good sweep as I pull in even with the SRi springs so reckon I'll be leaving a bit of spoiler behind with the Eibachs

[Trist78]

E10-65-007-02-22
Is the one I had ordered and just fitted over the weekend !

Was not expecting the bigger drop that I had !!

I have the SRI cdti 150 so I was infromed it will go down by about 15 mil but I would say a lot more maybe 25 mil or more.

I am also running 18s as well, hopefully I can get it cleaned this weekend and get picture up.